Showing posts with label power amplifier. Show all posts
Showing posts with label power amplifier. Show all posts

Rangkaian Amplifier Mini-Mini High Impedance Amplifier

Posted by Anonymous

Rangkaian Amplifier Mini-Mini High Impedance AmplifierRangkaian Amplifier Mini-Mini High Impedance Amplifier

Mini High Impedance Amplifier is an amplifier with 1 Watt and have a very high input impedance. This amplifier circuit can have a very high input impedance due to the use of two transistors in the input that is placed Darlington. Input impedance amplifier circuit is reached 20MOhm. Rangkaian Mini amplifier High Impedance Amplifier uses four transistors and an IC 741. Gain amplifier with high input impedance, we can provide the input signal from pernagkat with weak levels though.
Mini Series High Impedance Amplifier. Mini High impedance amplifier circuit is very cheap to make and quite simple. This amplifier circuit mengguanakan 9VDC supply.
More about → Rangkaian Amplifier Mini-Mini High Impedance Amplifier

Stereo Headphone Amplifier headset

Posted by Anonymous

Stereo Headphone Amplifier headset
Stereo Headphone Amplifier circuit uses DC voltage source 9Volt. As the name suggests this headphone amplifier circuit has inpur stereo and output to power about 50mW at 32 Ohm load. The series of "Stereo Headphone Amplifier" It uses mini-amplifier IC NE5534. Because of this NE5534 IC didalamanya there are 2 pieces mini amplifier then simply use 1 piece of IC NE5534 to Stereo Amplifier aHeadphone this. Stereo Headphone Amplifier series has this capability and low distortion, low noise. Stereo Headphone Amplifier circuit has a strengthening of 3.5 with 3.6 Vpp at 32 Ohm load.

Stereo Headphone Amplifier circuit. Sign Component Stereo Headphone Amplifier

P1 = 22K
R1 = 18K
R2 = 68K
R3 = 68K
R4 = 68K
R5 = 18K
R6 = 68K
C1 = 4.7uF/25v
C2 = 4.7uF/25v
C3 = 22pF
C4 = 220uF/25v
C5 = 220uF/25v
C6 = 4.7uF/25v
C7 = 22pF
C8 = 220uF/25v
J1 = 3.5mm Stereo Jack
B1 = 9V Alkaline Battery
IC1 = NE5532 or NE5534
SW1 = SPST Toggle Switch
More about → Stereo Headphone Amplifier headset

POWER INVERTER-MOSFET 1000 WATT

Posted by Anonymous

 power inverter mosfet 1000 watt title=

POWER INVERTER-MOSFET-1000 WATTThis power inverter circuit will provide a very stable “Square Wave” Output Voltage. Frequency of operation is determined by a pot and is normally set to 60 Hz. Various “off the shelf” transformers can be used. Or Custom wind your own for best results.

Additional MosFets can be paralleled for higher power. It is recommended to Have a “Fuse” in the Power Line and to always have a “Load connected”, while power is being applied. The Fuse should be rated at 32 volts and should be aproximately 10 Amps per 100 watts of output. The Power leads must be heavy enough wire to handle this High Current Draw! appropriate Heat Sinks Should be used on the RFP50N06 Fets. These Fets are rated at 50 Amps and 60 Volts. Other types of Mosfets can be substituted if you wish.

There ARE Limitations! I have had numerous requests for an Inverter for 1000 watts and Even MORE. Sorry I Don’t feel this is Practical. At 1000 Watts and operating from a 12 Volt Source, the Input Current will be close to 100 AMPS. That would Require a HUGH Size of a Primary Wire.

source: http://www.skema-elektronika.com/power-inverter-mosfet-1000-watt.html
More about → POWER INVERTER-MOSFET 1000 WATT

CARA MEMBAUT SPEAKER AKTIF

Posted by Anonymous

tool/alat yang dibutuhkan



catu daya scheme


power amplifier
1. Create a power supply circuit path and amps on the PCB board. In the manufacturing line, we can use a waterproof marker or a penyablonan theory.
Nich power supply circuit and PCB amplifier. was dissolved into the solution-clorida Ferry.

2. After you finish for jalurna, now we do the drilling on the PCB board in order to put the legs of the components that will be used. Watch out hand drilled ...
Ill lho ... ...
3. Enter the component - the component to the PCB board in accordance with the lines that have been made. Do not store the components - components
4. Soldering components.
5. Testing components - the components are connected or not with other components using multymeter. Take steps - these steps over and over - and over again
6. Create a box for the speaker to sound maknyos
7. After connecting all the components have been made n boxnya, connect to the sound source (type).
8. Enjoy your active peaker voice is
More about → CARA MEMBAUT SPEAKER AKTIF

Power Amplifier OCL 300W HIFI by MJ15004,MJ15003

Posted by Anonymous




For many application there's no substitute for sheer power- low efficiency speakers, outdoor sound systems, or maybe you like the full flavour of the dynamic range of a high power amp. Whatever your requirement-this super power module should fit the bill. How it works: The amplifier can be divided into three separate parts. These are : the input stage, which consists of Q1-Q9 , a high gain, low power driver; the output or power stage- witch only has a voltage gain of four but enormous power gain; and the power supply. The input stage is a complementary -differential network, each ''side" with its own current source. Each transistor in this stage is run at a collector currant of about 0.7mA. Emitter resistors are employed to stabilize the gain and improve linearity. The output of Q1-Q5 drives Q7 and Q9. The latter are virtually two constant-current sources run about 7mA collector current. With an input signal these "current" sources are modulated out of phase - the collector current of one decreases while the other increases. This configuration provides quite an amount of gain. In between the bases of these two transistors is Q8, the thermal sensing-bias transistor. The voltage across Q8 may be adjusted by TR1, thus setting the quiescent bias current for output stage. The output stage, Q10-Q11, Q13-Q14 and Q16-17, has a gain of about five, set by R44 and R28 plus R29. Diodes D4 and D6 prevent reverse biasing of Q10 and Q11 (otherwise the output would be limited). Protection of the output transistors is provided by Q12 and Q15 which monitor both current and voltage in the output transistors and bypass the base current if the limit is exceeded. Frequency stabilization provided by capacitors C6, C11, C12 and the RC networks R31/C10 plus R46/C15. Frequency response of the amplifier is set by C1 and C7 (lower limit), C6 sets the upper frequency limit. If you want use the Protection DC and Balance/Bridge circuits. All the transistors that are inside the interrupted line are placed on an aluminium corner and he screwed on a suitable heatsink. The transistors Q7,Q10,Q11, Q8, Q9, Q13,Q14,Q16 and Q17 placed on this aluminium corner, with suitable isolation from this


Part List

R1-19= 1Kohm 5W R34-35= 0.1ohm 5W C14-17= 100uF 100V
R2-3= 4.7Kohm R36-43= 39ohm C15= 100nF 250V polyester
R4-5= 22ohm R37-42= 5.6Kohm 1W Q1-2-3= BC547
R6-14= 10Kohm R38-41= 220ohm 5W Q4-5-6= BC557
R7-8= 1Kohm R39-40= 0.1ohm 5W Q7-11-12= BD140 or BC640
R9-23*=10K ohm R44-45= 0.1ohm 5W Q8= BC549
R10= 10ohm *see circuit sch. R46= 4.7ohm 2W Q9-10-15= BD139 or BC639
R11-13= 2.2Kohm R47= 100ohm Q13-14= MJ15004
R12= 22Kohm C1= 2.2uF 25V Q16-17= MJ15003
R15-16= 22ohm C2-6= 330pF ceramic TR1= 2K2 Trimmer
R17-18= 4.7Kohm C3-8= 100uF 100V F1-2= 5A Fuse Fast
R20-25= 390ohm C4-9= 100nF 250V D1-3= 5.1V 0.5W Zener
R21= 6.8Kohm C5= 100nF 100V polyester D2= 62V/5W Zener or 47v and 15V in series
R22= 4.7Kohm C7= 100uF 25V D4-5= 1N4004
R24-26-33= 220ohm C10= 1.5nF 100V polyester L1=10 turns diameter 1mm in 15mm diameter tube
R27-32= 100ohm 1W C11-12= 1.5nF 100V polyester
R28...31= 100ohm C13-16= 100nF 250V polyester *Use R23=6k8 for 4 ohm loudspeakers


SPECIFICATIONS

POWER OUTPUT 200W rms/8 ohm
310W rms/4 ohm
800W rms/8 ohm (Bridge mode)
FREQUENCE RESPONSE 20HZ-20KHZ +/-0.5dB
INPUT SENSITIVITY 1V for 200W/300W
HUM AND NOISE -105dB
THD <0.1%>




More about → Power Amplifier OCL 300W HIFI by MJ15004,MJ15003

Power Amplifier OCL 100W Mosfet J162 + K1058

Posted by Anonymous


PCB power amplifier ocl 100w Mosfet J162 + K1058
PCB power amplifier ocl 100w Mosfet J162 + K1058

Circuit power amplifier ocl 100w Mosfet J162 + K1058
Circuit power amplifier ocl 100w Mosfet J162 + K1058

More about → Power Amplifier OCL 100W Mosfet J162 + K1058

Power Amplifier Mini 2W+2W by TDA820M

Posted by Anonymous


PCB- Power Amplifier Mini 2W+2W by TDA820M
PCB- Power Amplifier Mini 2W+2W by TDA820M
Circuit - Power Amplifier Mini 2W+2W by TDA820M
This circuit Power Amplifier Mini 2W+2W by TDA820M.
Supply Volt 12V, Easy to build and Low cost.
More about → Power Amplifier Mini 2W+2W by TDA820M

Power Amplifier Super Small BCL 1.2W by IC TDA7052

Posted by Anonymous

PCB+Power+Amplifier+Super+Small+BCL+1.2W

This is Super Small Power Amplifier BCL 1.2W by TDA7052.

If you are gluttonous the ambit amplifies small-sized. I begs for to admonish this ambit

because tiny economize with the accessories is a little.

Power+Amplifier+Super+Small+BCL+1.2W
More about → Power Amplifier Super Small BCL 1.2W by IC TDA7052

Power Amplifier OCL 50W by MOSFET

Posted by Anonymous


PCB+-+50W+Power+Amplifier+Mosfet
PCB - 50W Power Amplifier Mosfet


Power+Amplifier+OCL+50W+by+MOSFET(with+PCB)
More about → Power Amplifier OCL 50W by MOSFET

LM1877 – Dual Audio Power Amplifier Schematics Datasheet and Application

Posted by Anonymous

The LM1877 is a monolithic dual audio power amplifier designed to deliver 2W/channel continuous into 8 Ohm loads. It was typically applicable in servo amplifiers, automotive products, tape recorders and players, AM-FM radio receivers, intercom system, multi-channel audio systems, and stereo phonographs.

LM1877 in Inverting Unity Gain Amplifier The following article contains detail description of LM1877, its features, connection diagrams, equivalent schematic diagram, absolute maximum rating, LM1877 – Dual Audio Power Amplifier electrical characteristics (including total supply current, output power, total harmonic distortion, output swing, channel separation, PSRR power supply rejection noise, noise, open loop gain, input offset voltage, input bias current, input impedance, DC output level, Slew rate, power bandwidth, and current limit).

In this article you will find also typical performance characteristics of LM1877, typical application in electronics compliant (with schematics of Stereo Phonograph Amplifier with Bass Tone Control, Inverting Unity Gain Amplifier, Stereo Amplifier, Non-Inverting Amplifier Using Split Supply, and Typical Split Supply) and physical dimension data. Find more information about LM1877 – Dual Audio Power Amplifier Schematics Datasheet and Application here – 9 pages of PDF filetype. (source: national.com)

More about → LM1877 – Dual Audio Power Amplifier Schematics Datasheet and Application

Crystal Radio (and other purpose) Audio Amplifier

Posted by Anonymous


Here is a simple audio amplifier using a TL431 shunt regulator. The amplifier will provide room-filling volume from an ordinary crystal radio outfitted with a long-wire antenna and good ground. The circuitry is similar in complexity to a simple one-transistor radio but the performance is superior (with the exception of the amazing one-transistor reflex ). The TL431 is available in a TO-92 package and it looks like an ordinary transistor so your hobbyist friends will be impressed by the volume you are getting with only one transistor and the amplifier may be used for other projects, too. Higher impedance headphones and speakers may also be used. An earphone from an old telephone will give ear-splitting volume and great sensitivity! The 68 ohm resistor may be increased to several hundred ohms when using high impedance earphones to save battery power.
More about → Crystal Radio (and other purpose) Audio Amplifier

Op-Amp Audio Amplifier

Posted by Anonymous


The above circuit is a versatile audio amplifier employing a low cost LM358 op-amp. The differential inputs give the amplifier excellent immunity to common-mode signals which are a common cause of amplifier instability. The dotted ground connection represents the wiring in a typical project illustrating how the ground sensing input can be connected to the ground at the source of the audio instead of at the amplifier where high currents are present. If the source is a power supply referenced signal then one of the amplifier inputs is connected to the positive supply. For example, an NPN common-emitter preamplifier may be added for very high gain and by connecting the differential inputs across the collector resistor instead of from collector to ground, destabilizing feedback via the power supply is greatly reduced.
More about → Op-Amp Audio Amplifier

4-Transistor Amplifier for Small Speaker Applications

Posted by Anonymous


The circuit above shows a 4-transistor utility amplifier suitable for a variety of projects including receivers, intercoms, microphones, telephone pick-up coils, and general audio monitoring. The amplifier has a power isolation circuit and bandwidth limiting to reduce oscillations and "motorboating". The values are not particularly critical and modest deviations from the indicated values will not significantly degrade the performance.

Three cell battery packs giving about 4.5 volts are recommended for most transformerless audio amplifiers driving small 8 ohm speakers. The battery life will be considerably longer than a 9 volt rectangular battery and the cell resistance will remain lower over the life of the battery resulting in less distortion and stability problems.

The amplifier may be modified to work with a 9 volt battery if desired by moving the output transistors' bias point. Lowering the 33k resistor connected from the second transistor's base to ground to about 10k will move the voltage on the output electrolytic capacitor to about 1/2 the supply voltage. This bias change gives more signal swing before clipping occurs and this change is not necessary if the volume is adequate.

As before, the two 4.7 ohm resistors may be replaced with a single 10 ohm resistor in series with either emitter.

More about → 4-Transistor Amplifier for Small Speaker Applications

Computer Audio Booster

Posted by Anonymous


Here is a simple amplifier for boosting the audio level from low-power sound cards or other audio sources driving small speakers like toys or small transistor radios. The circuit will deliver about 2 watts as shown. The parts are not critical and substitutions will usually work. The two 2.2 ohm resistors may be replaced with one 3.9 ohm resistor in either emitter.
More about → Computer Audio Booster

Simple LM386 Audio Amplifier

Posted by Anonymous


This simple amplifier shows the LM386 in a high-gain configuration (A = 200). For a maximum gain of only 20, leave out the 10 uF connected from pin 1 to pin 8. Maximum gains between 20 and 200 may be realized by adding a selected resistor in series with the same 10 uF capacitor. The 10k potentiometer will give the amplifier a variable gain from zero up to the maximum.




More about → Simple LM386 Audio Amplifier

Lm60 Lateral Mosfet Power Amplifier

Posted by Anonymous


As promised here are my thoughts on building and listening to your LM60 amplifier kit. I was very impressed with the delivery time after ordering (12days) The kit was supplied with good quality components, a good PCB with heavy solder tracks and component marking and a CD containing schematics, component list, build and test instructions. I think the inclusion of a photo of a completed board would be helpful. You did supply me one when I ran into a minor problem of my own making. in fact you could not have been more helpful.

For anyone able to solder the kit is simple and straightforward if the instructions are carefully followed but care in soldering is critical. I had a dry joint on 1 of my 2 boards which caused biasing and overheating problems when tested. With good help from Michael Chua this was resolved.

With the 2 boards (Stereo format) case mounted I connected to a single power supply, twin power supplies are recommended and probably best, but I only had a single supply to hand. This consisted of a 350Va - 24-0-24V toroidal transformer and 2 x 10,000mF caps in each power line and a 35amp solid state rectifier, giving me +/- 38vdc unloaded. This would result in a very slight reduction in power from the 60wpc output of the recommended power supply. Testing and biasing is simple following the instructions. DC offset in my case was about 5Mv and biasing set at the recommended 22Mv.

I connected to my 2 way monitor speakers (Ribbon Tweeters) with a frequency response from 35Hz - 40Khz and ran a a CD for listening test. I was totally amazed. Here was a very budget amplifier kit that had pretensions to be a Krell. There was no trace of hum or any other extraneous noise to interfere with the music even at high listening levels. Instruments and performers were very firmly locked into their own piece of the soundstage. Bass was very firm and deep and the Treble was as clean and open as a whistle.

Altogether a very balanced, clean and open sound. Remember the amplifier is not yet run in. After running for about 6 hours the heatsink temperature had risen 12 degrees over ambient level so no heat problems here.

This kit must be the absolute bargain for anyone who can solder and follow simple build instructions. It is the best kit amp I have ever heard and outperforms many amplifiers costing 20 times more. I would recommend this amp to anyone and am so impressed I will in due course return to Ampslab for a different more powerfull kit. Do not assume this kit is underpowered, it most certainly is powerfull enough for most circumstances but I am an inveterate meddler.

My congratulations to Michael Chua and staff at Ampslab. Keep up the good work in producing affordable audio gear. You may use any or all of this E Mail for publicity purposes.

from : ampslab.com

More about → Lm60 Lateral Mosfet Power Amplifier

POWER AMP SCHEMATIC 2N3055

Posted by Anonymous


c70
2N3055 + MJ2955

The c70 is a scaled down version of the c200. This does not imply an inferior performance, but rather a slightly simpler circuit due to the omission of the output protection network. Power output is less as the ever popular 2N3055 and MJ2955 are used. Properly constructed, it is surprising how good an amplifier can sound even with these "ancient" transistors.

Power supply requirements for 1 channel of c70 is a 25-0-25Vac, 100VA transformer for a supply rail of +-33Vdc. Filter capacitors are 2x10,000uF/50V. Output unclipped power is 45 Watts/RMS into 8 ohms and 70 Watts/RMS into 4 ohms.

For further information and power testing, kindly refer to the c200.




More about → POWER AMP SCHEMATIC 2N3055